FAQ
What Bottom Bracket do I need for my bike?
Choosing a Cane Creek bottom bracket takes two facts: your frame's bottom bracket shell and your crank's spindle diameter. Measure the shell width and bore, or look them up in your frame maker's spec. Threaded shells are usually 68 mm or 73 mm BSA, or T47 from 68 mm to 92 mm; press-fit shells are usually BB30, PF30 or PF41/BB92. Then match the spindle: 30 mm for eeWings, 29 mm for SRAM DUB, 24 mm for Shimano. The Cane Creek Hellbender 70 bottom bracket covers most combinations, though the PF41/BB92 version is 30 mm only.
What Bottom Bracket do I need for my cranks?
First you must ensure that the bottom bracket matches your frame's bottom bracket shell. Look up this information or measure your frame's shell width and bore diameter and reference this chart. Then select the bearing size that matches your crank’s spindle diameter. If you have eeWings, then any of our 30mm bottom brackets will work with the 30mm spindle of the eeWings crank. If you have a SRAM DUB crank, then any of our 29mm (DUB) bottom brackets will work with the 29mm spindle DUB cranks. For shimano cranks, choose the 24mm option.
What tools do I need to Install my Cane Creek Bottom Bracket?
BSA bottom brackets use a 12-notch, 46mm diameter tool like the Park Tool BBT-79.3. You can also use any other brand of 12 notch tool with these same dimensions.
T47 External bottom brackets use the Park Tool BBT-79.3 or similar tool.
T47 Internal bottom brackets use the Park Tool BBT-47-16 or similar tool.
PF30 bottom brackets use the Park Tool BBT-79.3 or similar.
BB30 bottom brackets use the Park Tool BBT-79.3 or similar.
PF41/BB92/BB86 version presses into the frame and needs a proper bearing or headset press with the correct adapters. Do not drive press-fit cups in with a hammer.
What's the difference between radial and angular contact bearings?
Radial and angular contact bearings look identical on the outside but differ internally. Angular contact bearings have angled inner and outer races that apply pressure (preload) to the ball bearings in the middle. Radial bearings have grooves on the inner and outer edges in which the ball bearings ride in, making them less affected by differences in alignment and preload as angular contact bearings. Angular contact bearings are thought to be longer lasting than radial bearings, but only if the bearings are preloaded properly and evenly. A small misalignment in a frame, or too much or too little preload force applied to the bearings will result in much faster wear than radial bearings.
Radial bearings are more forgiving, this is because the non angled surface helps reduce stress on the bearing cartridge caused by the weight of the load (you and your bike). Hellbender 70 bottom bracket bearings are radial. All of that being said, the real killer of radial or angular contact bearings, is corrosion which Hellbender bearings fight with the use of high grade, 440C stainless steel.
How do I identify my frame's bottom bracket shell before ordering a Cane Creek bottom bracket?
Measure the shell with the old bottom bracket removed, then match it to a Cane Creek bottom bracket. Threaded 68 mm - 73 mm wide shells with a 33.6mm diameter bore are BSA. Threaded shells with a much larger 47 mm diameter bore are T47. Unthreaded shells are press-fit: a 42 mm bore is BB30, a 46 mm bore is PF30 and a 41 mm bore in an 86.5 mm to 92 mm shell is PF41/BB86/BB92. Your frame maker's spec sheet usually lists this information. The Cane Creek Hellbender 70 bottom bracket is made for all of those shells, though the PF41/BB86/BB92 version comes in a 30 mm spindle only.
How do I make my Cane Creek bottom bracket last longer?
Keep water out of your Cane Creek bottom bracket and check it often. Never aim a pressure washer at the bottom bracket shell, wash with low-pressure water from above, and dry the bike rather than leaving it wet. Check for play and roughness every time you clean the drivetrain: rock a crank arm side to side, then drop the chain off and spin the cranks by hand. If you feel roughness or play, it's a good time to remove the cranks and clean and regrease the assembly, making sure to wipe dirt off of all the overlapping surfaces. Hellbender stainless bearings are designed to last for many seasons and Hellbender ceramic bearings have a lifetime guarantee. If a basic clean and regreasing does not solve the grittiness, then contact Cane Creek to source replacement bearings.
How do I remove a press-fit Cane Creek bottom bracket without damaging my frame?
Removing a press-fit Cane Creek bottom bracket needs a proper removal tool and slow, even work. Pass the removal tool in from the opposite side of the frame so its petals expand behind the cup, keep it square to the shell, and drive it out in small even taps rather than one hard blow. Never lever on one edge with a screwdriver or a punch. On a carbon frame, it's best to take your bike to a shop.
How long do Hellbender bottom bracket bearings last in wet, muddy conditions?
It's nearly impossible to put a specific lifespan on bearings because every use case is wildly different, but Hellbender stainless bearings are designed to last multiple seasons and Hellbender ceramics are guaranteed for life. The Hellbender 70 and Hellbender 110 bottom brackets both use dual lip seals and heavy grease to protect the bearing balls and races. You can prolong the life of your bearings by regularly checking bottom bracket preload (by feeling the cranks for lateral play) and minimizing water saturation from washing. If you must wash your bike with water, do not aim high-pressure spray directly at the cranks or bottom bracket area.
My Hellbender bottom bracket creaks. How do I fix it?
A creaking bottom bracket is usually dry or loose rather than worn out. Start by removing the cranks and cleaning all overlapping surfaces, including spacers and bearing dust covers. Once the crank, spacers, and BB are all thoroughly wiped down, apply a thin film of new grease. Re-install the crank and reset crank preload so there is no side-to-side play. Rule out other sources too: pedals, chainring bolts, crank fixing bolt, seat clamps, and pivot bolts can all creak in ways that sound like a bottom bracket.
What torque should I use when installing a Cane Creek bottom bracket?
All threaded Cane Creek bottom brackets should be torqued to 40Nm using a high-quality and calibrated torque wrench. Press-fit 41 bottom brackets should be pressed firmly and squarely into the frame using an appropriate bearing press such that the flanges on the bearings seat tightly and evenly against the frame.
Can I replace the bearings in my Cane Creek bottom bracket myself?
While we do sell replacement bearings for our bottom brackets, pressing a cartridge bearing in or out of an alloy cup is delicate and precise work. We recommend taking your bottom bracket and new bearings to a bike shop to perform the bearing swap.
What bottom bracket spacer kits does Cane Creek sell?
Cane Creek sells two bottom bracket spacer kits. The Hellbender BB Spacer Kit for BSA shells contains two 2.5 mm bottom bracket cup frame spacers. The 30 mm Crank Spindle Spacer Kit contains two each of 5 mm, 2.5 mm and 1 mm spindle spacers. Cup spacers sit between the bottom bracket cup and the frame to set cup position; spindle spacers sit on the crank spindle to space the crank evenly in the frame. Spindle spacers do not need to match your bottom bracket brand, only the spindle diameter.
Is my Hellbender bottom bracket covered by a lifetime warranty?
That depends on which Hellbender bottom bracket you have. The Hellbender 110 bottom bracket is covered by Cane Creek's 100% Lifetime Guarantee including bearings, for units purchased after 28 August 2019. The Hellbender 70 bottom bracket is listed at one year. Hellbender branding does not automatically mean lifetime coverage, and this is the most common warranty mix-up in the Cane Creek bottom bracket range. Claims go through a Cane Creek dealer or Cane Creek support.
How much do Hellbender 70 Bottom Brackets weigh?
BSA Threaded 30mm bearing – BAI0143 – 92g
BSA Threaded 29mm bearing – BAI0156 – 97g
PF30 30mm bearing – BAI0145 – 123g
PF30 29mm bearing – BAI0158 – 127g
BB30 30mm bearing – BAI0144 – 100g
BB30 29mm bearing – BAI0157 – 105g
T47 30mm bearing – BAI0160 – 141g
T47 29mm bearing – BAI0163 – 145g
PF41/92 30mm bearing only – BAI0159 – 78g
Does Cane Creek make a bottom bracket for 24 mm Shimano or 29 mm SRAM DUB cranks?
Yes, the Hellbender 70 bottom bracket is made in 24 mm for Shimano cranks and 29 mm for SRAM DUB cranks, as well as 30 mm for cranks such as eeWings.
Is the Hellbender 70 a headset or a bottom bracket?
Hellbender 70 is the mid-range headset AND bottom bracket line from Cane Creek. Both units get their name from the Hellbender stainless steel bearings that provide long term reliability and performance. Hellbender 70 headsets and bottom brackets are available in a range of colors through Cane Creek's Chroma Studio.
What's the difference between the Hellbender 70, Hellbender 110, and 110 Ceramic bottom brackets?
Hellbender 70 is the mid-range bottom bracket option from Cane Creek. It runs on Hellbender stainless bearings that offer a long life and smooth performance and it offers great bang for your buck. It's also available in colors through the Chroma Studio collection. Hellbender 110 was Cane Creek's long-standing premium option, using XD-15 ceramic bearings that carried a lifetime guarantee and the smoothest possible performance. It came in a two-tone black and gold colorway. The more modern 110 Ceramic is the evolution and replacement for the Hellbender 110. It ditches gold and moves to a two-tone black and silver color to match Cane Creek's 110 Ceramic headset and uses a new Hellbender ceramic bearing. It's actually more affordable than the previous 110 model and makes the lifetime-guaranteed smooth performance of ceramic bearings more accessible to riders.
How do I know what spacers to use with my Cane Creek bottom bracket?
For use on a 73mm wide BB shell, eeWings Mountain uses a black, 1.75 mm chamfered spacer that sits directly against the drive-side arm plus one additional 2.5mm bottom bracket spacer. The 2.5mm spacer is included with all Cane Creek BSA bottom brackets and the chamfered 1.75mm spacer comes with the cranks. On 68mm shells, eeWings Gravel uses a 1 mm silver chamfered spacer (included) on the drive side only. No other spacers are required. If you've lost any of these spacers, Cane Creek sells them individually as replacements.
Can I use a Shimano XTR 12 speed chain with eeWings?
Yes, to use eeWings Mountain with any Shimano 12 spd mtb drivetrain, simply use one of our Cane Creek chainrings. Cane Creek chainrings have a tooth profile that works with Shimano Hyperglide+ and Linkglide 11- and 12-speed chains as well as SRAM Eagle and Flat Top 12- and 13-speed chains. Match the chainring offset to your drivetrain's chainline: 3 mm offset for Shimano XT M8100 and XTR M9100 at 52 mm, and 0 mm offset for XT M8200 and XTR M9200 at 55 mm.
What chainring do I use on my eeWings?
First generation eeWings (2018 - 2025) use SRAM 3-bolt direct mount interface. There are many brands that make chainrings using this mounting configuration. All second generation eeWings (2025-2026) use the more contemporary SRAM 8-bolt direct mount interface. Cane Creek produces our own chainring for the 8-bolt crank. These chainrings are designed to work with nearly all modern 12 and 13spd speed drivetrains. To determine exactly what offset chainring you need for your particular bike, count the bolts on your drive-side arm first, then choose 0 mm or 3 mm offset using the Cane Creek chainring and chainline setup guide. Cane Creek also offers spiders to mount Shimano GRX, Ultegra and Dura-Ace rings to eeWings.
What chainring sizes does Cane Creek make for eeWings?
Cane Creek chainrings come in 30T, 32T, 38T, 40T, 42T and 44T. If you want a 34T or 36T on current eeWings, you will need an 8-bolt direct mount ring from another brand. Cane Creek chainrings do not fit eeWings G1 (3-bolt).
Which chainring offset do I need for my eeWings, 0 mm or 3 mm?
eeWings chainline is set by the chainring offset, not by the crank. Choose 3 mm offset for a standard Boost mountain bike running SRAM Eagle, Shimano XT M8100 or XTR M9100, which gives a 52 mm chainline on eeWings Mountain. For gravel and road, SRAM XPLR 13-speed, SRAM Red, Force and Rival AXS and Shimano GRX, choose 3mm offset as well, which gives 47 mm on eeWings gravel. If using eeWings Mtn, choose 0 mm offset chainrings for SRAM Transmission and Shimano XT M8200 and XTR M9200, which produces a 55 mm chainline.
Can I run a Wolf Tooth or oval chainring on my eeWings?
Yes, as long as the ring matches your eeWings generation. Current eeWings use the 8-bolt direct mount pattern used by modern SRAM cranks, so 8-bolt aftermarket rings, including oval ones, will mount. eeWings G1 (3-bolt) needs a 3-bolt direct mount ring instead. Wolf Tooth, for example, lists direct mount rings for Cane Creek and SRAM cranks in both SRAM and Shimano Hyperglide+ tooth profiles. Cane Creek does not test third-party chainrings, so check the maker's fitment and offset notes before ordering.
What are Cane Creek chainrings made of and how much do they weigh?
Cane Creek chainrings are CNC-machined from 7075 aluminum and come in black and smoke (titanium color-matched) colors. Cane Creek publishes two weights: 58g for the 30T mountain ring and 106g for the 40T gravel ring. Weights for the other tooth counts are not published. Every Cane Creek chainring uses the 8-bolt direct mount interface and will not fit eeWings G1 (3-bolt).
What are Electric Wings and which e-bike motors do they fit?
Electric Wings are Cane Creek's titanium e-bike crankset, designed to fit the common ISIS Drive motor spindles found on many Bosch, Brose, Panasonic, TQ, Yamaha motors, and more. Check your bike manufacturer's motor specs or visit Canecreek.com for a list of compatible bikes and motors.
What torque does Electric Wings need, and how is it installed?
Electric wings are installed with a single, 8mm fixing bolt, torqued to 52Nm. Fit the Electric Wings arms 180 degrees apart, use the supplied Ti-Prep on the threads, and re-check the 8 mm fastening bolt torque monthly. Pedal washers are not required with Electric Wings. Use a calibrated torque wrench.
Can I use eeWings cranks on my e-bike?
E-bikes with a mid-drive motor need Electric Wings, Cane Creek's titanium crankset for ISIS Drive motor spindles. Standard eeWings can be used on e-bikes only if they use a standard bottom bracket shell and a hub-drive motor.
How much does Electric Wings weigh and what arm lengths are available?
Electric Wings are currently only available in 165mm lengths. A set weighs 383g including all hardware.
What is the warranty on Electric Wings?
Electric Wings carry a limited five-year warranty from the date of original retail purchase to the original owner. The warranty covers defects in materials and workmanship. Contact Cane Creek support with your purchase date and proof of purchase to start a claim.
Can I use a direct mount spider with eeWings Gravel?
Yes, eeWings Gravel cranks use the 8-bolt direct mount interface, popularized by modern SRAM cranksets. Any 8-bolt spiders or power meters can be used with eeWings. We also produce our own spiders that allow eeWings to be used with Shimano Ultegra, Dura-Ace, and GRX chainrings.
Can I use the Cane Creek preload assembly on another crankset?
Yes, the Cane Creek Crank Preloader is compatible with all SRAM DUB cranks, as well as any other crank that uses a 30mm spindle, such as those made by Easton or Raceface. To replace the plastic preloader on any SRAM DUB crank (road, mountain, or gravel) simply remove the existing preloader and pry off the plastic thread ring that it attaches to. You will need to use a pick or very small flat head screw driver to pry off the old thread ring. Once removed, use a very small amount of super glue to secure the silver Cane Creek thread ring to your crank spindle.
What chainring spiders does Cane Creek make for eeWings?
Cane Creek makes four 8-bolt spiders for current eeWings and one for eeWings G1. The 8-Bolt GRX spider has 110 mm and 80 mm 4-bolt patterns, a 2.5 mm offset, a 47 mm chainline and weighs 80 g; it fits Shimano GRX 600 and 800 to 820. The 8-Bolt Ultegra 8100 and 8-Bolt Dura-Ace 9200 spiders are 110 mm 4-bolt with a 7.5 mm offset, a 44.5 mm chainline and weigh 78 g. There is also an 8-bolt to 110 mm 5-bolt spider for 1x, and a 3-Bolt to 5-Bolt spider for eeWings G1. Cane Creek does not publish a spider bolt torque.
Can I use my eeWings with a T47 Bottom Bracket?
Yes! eeWings are compatible with both internal and external style T47 bottom brackets, provided they are designed to accept a 30mm crank spindle. If your bike uses a T47 bottom bracket, but currently has SRAM or Shimano cranks installed, you will need to purchase a new bottom bracket for 30mm spindle. Cane Creek makes the Hellbender 70 bottom bracket in a T47, 30mm configuration and is a perfect match for eeWings.
Do eeWings work with superboost spacing?
In most cases, eeWings fit on bikes that use Superboost (157x12mm) rear hub spacing. eeWings use a spindle length that accommodates most modern applications, including Superboost. It is often required to use a 0mm offset chainring for this application.
Should I use anti-seize or grease on eeWings?
Since all current 8-bolt eeWings use stainless steel hardware (fixing bolt and chainring bolts) anti-seize is NOT necessary in most applications. It is recommended to use blue loctite on the main fixing bolt and standard assembly grease on the chainring bolts and pedal threads. The only scenario where anti-seize is needed is when using pedals with titanium spindles. Older, first generation eeWings shipped with a tube of Ti-Prep because those cranks originally had titanium fixing bolts and chainring bolts. Since the current cranks swapped all the hardware to stainless steel, the ti-prep is no longer included.
What Bottom Bracket shells are eeWings Gravel compatible with?
eeWings Gravel can be mounted on any modern road bike bottom bracket standard. The cranks use a 30mm spindle, so you just need to make sure the bottom bracket that corresponds with your frame is for 30mm spindle. We make Cane Creek bottom brackets that allow eeWings Gravel to be fitted to the following: 68mm threaded (BSA & T47 external), 86.5mm threaded (T47 internal), 68mm press-fit (BB30 & PF30), and 86.5mm press-fit (PF41).
What Bottom Bracket shells are eeWings Mountain compatible with?
eeWings Mountain are compatible with 73mm and 92mm threaded shells, and 73mm, 89.5mm, and 92mm press-fit shells. This means the cranks are compatible with most mountain bikes, except for Downhill and Fatbikes. The cranks use a 30mm spindle, so you just need to make sure the bottom bracket that corresponds with your frame is for 30mm spindle. We make Cane Creek bottom brackets to allow the cranks to be fitted to most applications: BSA, T47, PF41, BB30 & PF30.
What arm lengths are offered?
eeWings Gravel are currently offered in 165mm and 170mm. eeWings Mountain are offered in 155mm, 160mm, 165mm, and 170mm. Due to significantly falling demand in recent years, we no longer produce eeWings in 172.5mm or 175mm lengths.
What is the spindle diameter of eeWings?
eeWings use a 30mm spindle for ultimate stiffness-to-weight characteristics. Make sure the bottom bracket on your bike is for 30mm spindles, or purchase a Cane Creek bottom bracket to complete the upgrade.
What is the spindle width?
eeWings Gravel have a max useable spindle width of 92.5mm. eeWings Mountain have a max useable spindle width of 98.25mm.
What is the warranty on eeWings?
The first generation, 3-bolt eeWings came with a 10 year warranty, a bold and uncommon term when the cranks were released in 2018. All later generation 8-bolt eeWings come with a limited lifetime warranty. These are some of the most durable cranks on earth and we're proud to stand behind them as the last cranks you'll need to buy. For details on our warranty coverage and process, see the warranties page on canecreek.com.
What's the difference between eeWings Gravel and eeWings Mountain?
Not very much! The only difference is the spindle width. The mountain cranks use a roughly 5mm wider spindle to accommodate for the wider bottom bracket shells used on mountain bikes. The arms, materials, and construction of the cranks are otherwise identical.
Are eeWings compatible with bikes and drivetrains that use SRAM DUB WIDE cranks?
Yes, eeWings are compatible with SRAM DUB WIDE. To make sure you match the WIDE chainline, you'll need to select a 0mm offset chainring for mountain bike use, or a 3mm offset chainring for road and gravel use.
Do eeWings fit downhill bikes?
No. Though eeWings would be stiff enough and strong enough for DH use, the spindle is not long enough to fit through the wider bottom bracket shells (83mm threaded) used on most downhill bikes. If your DH bike uses a 73mm threaded or 92mm press-fit BB shell, then eeWings ARE compatible.
How much do the eeWings Gravel weigh?
The 165mm gravel cranks weigh 398 grams. This includes all items included in the assembly (arms, spindle, fastening bolt/washer, chainring bolts, spindle spacer, preload assembly).
What are the eeWings made of?
The eeWings arms are Grade 9 Ti-3AI-2.5V titanium because this particular ti alloy is best for making drawn and formed tubes. The hirth joint/chain ring interface, spindle, pedal inserts, and preloader screw are Grade 5 Ti-6AI-4V titanium, as this alloy is better for machined parts. The main fixing bolt is 17-4 stainless steel. The required 1.75mm spindle spacer, and preload assembly (thread ring and spacer ring) are made of 7075 aluminum.
What is the Q-Factor on eeWings?
eeWings Gravel have a Q-factor of 160mm. eeWings Mountain have a Q-factor of 176mm.
Why did my eeWings not come with pedal washers?
eeWings do not require the use of pedal washers. Washers may be used if so desired for bike fit purposes, but remember that the Q-factor on eeWings is already wider than most other cranks so the use of washers is likely not necessary.
What kind of material do I use to touch up the brushed finish of my eeWings?
3M 96 Scotchbrite, green color, Medium Duty Scouring Pads can be used to remove scuffs, dirt, and small abrasions from eeWings. Take care to not run the Scotchbrite over the lasered graphics.
Can I run a front derailleur or a 2x drivetrain with eeWings?
Yes, using the right Cane Creek spider. Current 8-bolt eeWings can be run with modern SRAM 2x drivetrains using SRAM's own direct mount 2x chainring sets. For Shimano, Cane Creek offers 2x compatibility for GRX, Shimano Ultegra R8100, and Dura-Ace R9200 using their own spider that mates to the Shimano chainrings. Cane Creek's own direct-mount chainrings are 1x only, and the 8-Bolt to 5-Bolt spider is sold as 1x only.
How do I set the preload on eeWings?
Fit the eeWings crankset, torque the drive-side fixing bolt to 52 Nm, then turn the eeWings preload spacer ring clockwise by hand until snug and side-to-side crank play disappears. Do not overtighten! Lock the preload ring by tightening its 2.5 mm hex bolt to 1.4 Nm. If the cranks feel tight or bind after preload, there's likely too much preload on the bearings. Back the ring off slightly and re-check for play.
What torque do I use on eeWings crank and chainring bolts?
eeWings 8-bolt torque specs are 52 Nm for the drive-side crank fixing bolt, 4 Nm for the chainring bolts and 1.4 Nm for the preload spacer ring bolt. The fixing bolt takes an 8 mm hex, the chainring bolts take a T20 torx and the preload spacer ring bolt takes a 2.5 mm hex. Use a calibrated torque wrench on all three. These figures are from the current eeWings 8-bolt instruction manual. If you have eeWings G1 (3-bolt), use the manual supplied with those cranks.
How do I remove my eeWings cranks?
Release the eeWings preload first, then undo the crank bolt. On current 8-bolt eeWings, unscrew the 2.5 mm hex bolt on the non-drive side and turn the preload nut counterclockwise until all preload is off the crankset, then undo the 8 mm hex fastening bolt on the drive side and draw the arms off the 30 mm titanium spindle. Cane Creek states that no crank puller and no proprietary tool is required for eeWings. On refitting, torque the fastening bolt to 52 Nm, reset preload by hand, and lock the preload ring bolt at 1.4 Nm.
What tools do I need to install eeWings?
To install current 8-bolt eeWings you need a torque wrench with an 8mm hex bit that can apply up to 52Nm for the crank fixing bolt, a T20 torx for the chainring bolts, and a 2.5mm hex for the preload spacer ring bolt. You also need the right bottom bracket tool for your frame, a 12-notch 46 mm tool such as a Park Tool BBT-79.3 for BSA, T47 external, BB30 and PF30 Cane Creek bottom brackets. No crank puller and no proprietary Cane Creek tool is required for eeWings.
Can I convert my eeWings G1 (3-bolt) cranks to the 8-bolt chainring interface?
No, Cane Creek does not offer a conversion from eeWings G1 (3-bolt) to the 8-bolt chainring interface. The chainring mount is part of the eeWings G1 arm and spindle assembly, so moving to 8-bolt means buying a current 8-bolt eeWings crankset.
Can I use the new 8 mm crank bolt on my eeWings G1 (3-bolt) cranks?
Yes. Cane Creek sells the eeWings G1 Spindle Bolt and Washer Kit in an 8 mm drive version (BAI0400). This uses the new 8mm drive bolt with the original washer. The 8 mm hex was adopted because a 14 mm hex is hard to source in a shop or mid-ride.
How do I tell whether I have eeWings G1, G2, or G3?
Start by counting the chainring bolts on the drive-side eeWings crank arm. eeWings G1, sold from 2018 to 2025, uses a 3-bolt direct mount interface and originally shipped with a 14 mm hex crank fixing bolt. G2 and G3 eeWings use an 8-bolt direct mount interface with eight T20 chainring bolts and an 8 mm hex fixing bolt. G3 kept the 8 bolt direct mount interface, and went to a full machined pedal end instead of a welded pedal nut and end cap.
What chainrings fit eeWings G1 (3-bolt) cranks?
eeWings G1 (3-bolt) takes 3-bolt direct mount chainrings built to the SRAM pattern, or 110 mm x 5-bolt rings fitted with the Cane Creek 3-Bolt to 5-Bolt spider. The current Cane Creek chainring does not fit eeWings G1, because that ring is 8-bolt only. Aftermarket brands do still make 3-bolt direct mount rings, so eeWings G1 owners have options, but not from the current Cane Creek chainring range.
What warranty applies to my eeWings G1 (3-bolt) cranks?
The eeWings G1 (3-bolt) carries a 10-year warranty to the original retail owner. Coverage is for defects in materials and workmanship to the original owner and excludes crash damage, abuse, neglect and finish wear. Contact Cane Creek support with your purchase date to confirm the term on your cranks.

